How to Make the Perfect Pillowcase


 Materials Needed:
(3) Complementary Cotton Woven Fabrics
Rotary Cutter or Scissors
Cutting Mat
Sewing Machine



Use this tutorial to make the Perfect Pillowcase, a unique accessory for any bed. Sized to fit a standard or queen-sized pillow.Begin by cutting your fabric. You will fold your fabric down the middle and line up opposite selvage edges. Smooth out fabric and make sure it is as straight as possible before cutting. At the completion of your cut, you will have a long rectangle that still contains selvage edges on both short sides.

Main Fabric - 27" x 44/45"

Cuff Fabric - 9" x 44/45"

Accent Trim - 3" x 44/45"

Cut all three fabrics based on the sizes listed above. Mix and match your fabrics to create an eye-appealing design.

three pieces of coordinating material laid on a cutting mat

Fold the main piece, wrong sides together, and lay it upon your work station. Make sure your selvage edges are lined up precisely. Repeat for the cuff and accent piece. Line up all three cuts at the folded edge and lay them on top of each other.

coodinating fabric lined up on a table

Ensure that the folds are well lined up.

Cut the selvage edge straight by using your ruler and mat to ensure a clean line.

Straight cut shown below. You now have three pieces of fabric with the same width.

Fold accent piece in half lengthwise, wrong sides touching, and press to create a sharp fold.

Put cuff on workstation, right side up. Place main fabric on top of that, right side up. Ensure that the top edges line up. Finish the fabric "sandwich" with the accent piece, raw edges lined up with the other two fabrics' edges. The folded edge of the accent piece will be facing downwards.

Slowly roll up the main fabric, careful not to roll the cuff along with it. Stop rolling before you get to the accent piece.

Make a burrito roll by gently pulling up the bottom of the cuff and lining it up with the edge of the sandwiched fabrics. Pin or clip the center to secure. (Make sure you have all layers pinned/clipped.)

Take your time and continue pinning down the length of the fabric sandwich.

Sew with 1/4" seam allowance, back-stitching at beginning and end. Gently pull the fabric completely out of the "burrito".

Press fabric, taking care to crease the fold of the cuff well.

After material is ironed, fold the fabric, wrong sides together, and line up the raw edges to prepare to sew.

Make sure the seams of the cuff and accent piece are lined up and clip or pin. Sew with 1/4" seam allowance down the two raw edges of the pillowcase.

Cut seam allowance down to 1/8" using a ruler and a rotary cutter. Be careful not to cut the stitching of the seam. You are making room for the French Seam created in the next step.

Turn the pillowcase inside out. This part can be a bit tedious so take your time. Work the seam you just made to the edge of the pillow case with your fingers. Rub the seam a few times between your index finger and thumb until you feel/see it extend out.

If you have trouble, put a hand inside the pillowcase and poke the seam out. If you skip this part, you will end up sewing too much fabric in the next step when you create your French Seam.

As you continue to pull the seam flush around the edges, pin or clip as you go to keep your material in place.

Sew around the pinned/clipped edges with a 1/4" seam allowance, back-stitching at the beginning and the end. This creates your French Seam.

French Seam interior view of cuff.

Turn pillowcase right-side out. Press.

You have completed the Perfect Pillowcase!

Mix and Match your favorite fabrics to create your own home decor.

This pillowcase was created with fabrics from Michael Miller's Ice Cream, You Scream collection.

Feel free to take a look at our fabric collection to find your own inspiration.

 


Leave a comment


Please note, comments must be approved before they are published